Pictured above: Here are the coils on the water bottle bracelet. I can imagine a picture frame done in the same method looking really pretty!
On Cool2Craft today, I showed how to make some cool items out of magazine pages. Some of you may remember from a few months back when I showed pictures on here of my water bottle bracelets. One of them was covered with coils made of magazine page paper. Well today, I demonstrated how to expand on one of those coils and turn it into a bowl.
Get started by ripping those pages out of an old magazine. I can usually get about 8 strips from one magazine page. When I rolled up 12 strips, I ended up with a coil that was about 1 1/4 inches in diameter to give you an indication of how many pages you’ll need.
From the pages, you’ll want to cut or tear strips (along the longest edge of the page or I guess you could think of it as tearing them vertically down the page). The strips should be roughly 1 to 1 1/2 inches wide. You could certainly use a paper cutter to cut the strips to size but I found a ruler with a nice metal edge that was about an inch wide. I laid the ruler down on the page and just tore. This meant that I could do it pretty much anywhere without having to pull out the big paper cutter and it meant I didn’t have to measure out each and every strip because the ruler did it for me. If you decide to tear your strips too, don’t worry. The raw edges won’t show after the folding procedure.
For each strip, you need to fold it in half lengthwise.
Open it up and then fold in from each of the edges to meet that middle fold. Make good sharp creases. I find it easier to glue and coil them if they have good creases in them!
Now close the whole thing up along that center fold. Someone in Cool2Craft likened it to double fold bias tape which is a good way to think of it. When it’s all folded, your strip that started as 1 inch would now be 1/4 inch wide.
You’re going to join the strips together by tucking the end of one inside of another and securing it with glue stick. Some hints I’ve learned along the way: for the very first strip I’m going to use right in the center of the coil, I glue the whole strip together (inside the fold). Don’t do this for any others – just the very first strip. For the other strips, I put a little dab of the glue at one end to hold just that end closed and then, that’s the end I tuck into the next strip, securing it there with more glue.
In the pictures above, I’m showing you where I put a dab of glue and then pressing the two sides together to close off one end.
I work with four strips glued together at a time. This means you aren’t stopping to add on new strips every couple seconds as you coil but it also isn’t so long that it becomes cumbersome and hard to handle without ripping or having it fall apart.
In the pictures above, I’m showing you where I put dabs of glue and then insert the strip with the glued end into another strip for joining.
To begin the coil, take that first strip and give it a little fold at one end. You’ll be able to roll the rest of the paper around that fold to create a coil of paper. If it’s easier for you, you can use something like a toothpick or bamboo skewer to begin the coil around instead of making the little fold. As you begin to roll the coil, you want to dab on a bit of the glue every couple inches or so to hold the coil together. I found it especially important to put glue in those spots where the pieces were seamed together. You may find you need to glue a little more often once the coil gets bigger but you don’t want to glue it completely together or it won’t expand out into the bowl shape. When you get near the end of the length of strips you’re coiling, leave a little “tail” hanging out so you have a place to join on another length.
In the pictures above, you can see the “tail” I left as I was coiling to be able to join another set of 4 strips on and continue coiling.
Some people like to start using a bowl they have as a mould for this once they have a bit of a base created. Turn the bowl upside down and put the base coil you have on the bottom of the bowl. They then continue to coil around the bowl. I found that awkward. I have a permanent hand injury so my fine motor control and dexterity isn’t always what it should be so perhaps that was the issue for me. I found it easier to continue making the coil flat against my work surface and then when I had a coil big enough to turn into a bowl, I placed it on the mould for the coating stage.
Pictured above, the coiled paper being pressed down over the bowl I’m using as a mould so I can coat it with a clear sealant.
For the coating, I covered my bowl with plastic wrap to protect it. I placed my coiled piece over the bottom of the boil and gently pressed it down into a bowl shape. While it was still on the bowl, I coated the outside of it with Liquitex Gel Medium (the one I used is the Gloss Super Heavy Gel). This worked wonderfully! I’ve heard of other people using shellac or Mod Podge with good results as well. I let the gel medium dry and then applied a second coat. When that was dry, it was stiff and sturdy enough to remove from the bowl mould. I could now coat it with the gel medium (2 coats once again) on the inside of the bowl. Once that dried thoroughly, the bowl holds its shape very well.
Pictured above, the bowl drying after having been coated inside and out with 2 coats of Liquitex Gloss Super Heavy Gel Medium.
Obviously this bowl can’t be washed and isn’t food safe but it makes a very pretty decorative bowl. My daughter’s taking this one to university to use on her desk for holding paper clips and such.
Leave it flat like I’ve done in the picture above and it can serve as a trivet or coaster.